Both Xerox and Okidata have taken the world by storm with their innovative technologies. However, there are still many error codes that baffle users. Here we discuss common error codes and their troubleshooting tips.
Error message: job canceled
This error message occurs when you have deleted a scan job before it could be completely transferred into the scanner’s database. Try resending the scan and make sure you do not delete the job.
Error message: failure in the remote directory’s lock
This error could happen because the folder with extension .ick was not removed properly after the scan. It could also occur if the destination disk is completely full. Maybe the directory or the volume for scan database has been incorrectly provided in the Xerox device. Try to remove the .ick folder and resend scan.
Error message: Invalid protocol
This type of error message occurs when the particular protocol has not been enabled inside the Xerox printer. You need to enable the particular protocol.
Error message: File transfer failure
This kind of error message happens when the network is down or if the disk is full or if the scan database path is incorrectly specified. You need to check the status of the network as well as amount of disk space.
Error message: system canceled job
This error message occurs when the sensors for the document handler is defective. It could also happen if these sensors have not been installed properly or if a person is lifting the edge of a large document from the trail sensor. You need to resend the scan and if the problem isn’t because of a person then it is definitely hardware or a setup issue.
Error code: 71
This error code in your Okidata device indicates it is a fuser error. Make sure to replace your fuser. Or else try checking the main board.
Error message: Error engine
This happens usually in the Oki Laser 400 series. Make sure to replace the ROM chip first. If this does not work, try replacing the circuit board of the engine controller.
Error code: 173
This error code means that the fuser temperature is low. You need to replace either the fuser or the thermistor inside the fuser.
Error message: fatal error 140
This error code 140 means the drum down and up process of the images are not functioning properly. The error code 140 means the error is with the yellow drum while 141 and 142 indicate problems with the magenta and cyan ones respectively. Try reseating the drums for image first. Then try reseating toner cartridges. You also will need to reseat the assembly for the sensor spring for the contact.
Error code: 020
This is another of the fatal error codes and indicates a power problem in the network. You need to make sure that the power cable is in direct connection with the outlet on the wall. You could also try replacing the cable or use a different network if this does not solve it.
About the Author:
This Article is written by James Kara Murat from PrintCountry.com, the contributor of Printer Reviews. More information on the subject is at Xerox, Okidata Error Codes and How to Fix Them, and related resources can be found at Xerox Toner Cartridges.
Showing posts with label Codes. Show all posts
Showing posts with label Codes. Show all posts
Monday, August 18, 2008
Dell Laser Printer Error Codes, How to Fix Them
The Dell Laser Printer is one of the best around in the market. However, many users complain about the numerous error codes they frequently receive. Here are some troubleshooting tips on fixing these errors effectively.
Error code: 004-332
This type of error code implies that you need to restart the printer again. However, do check to see if toner cartridges are seated in the proper position. Also ensure that they have been locked in. This is an error commonly associated with the Dell 3100cn laser printer.
Error code: 016-370
This is yet another error message asking you to restart the printer. You need to switch off the printer and then connect it via the USB cable. Press the hold and cancel buttons simultaneously. Then power on the printer again. On your LCD display you should typically see a message saying ‘ready for download mode’. You will then need to initialize the firmware update process.
Error code: 009-360
Sometimes the Dell laser printer only recognizes the yellow toner as ‘missing’. Hence you need to replace the Dell toner with a new one. It can happen when the toner is a remanufactured one with a different chip.
Error type: Not printing black text
This type of error happens because of a problem with the power supply. You need to check if the I/O cable is connected properly or not and that all connections are in place.
Error type: Printing text in red
At certain times you might be able to print perfectly well the first two times and then you see the text being covered in red color. This can happen if the unit is still not properly clean. You could try cleaning the tube.
Error message: Insert yellow toner
Sometimes in spite of replacing the yellow toner in your Dell 5100 cn laser printer you might still get this error message. Try to change the black cartridge. You could also check to see if the toner cartridges are locked appropriately.
Error message: Print head error
This type of error message typically happens when the printer head is not clean enough. You could try installing software that is used to clean the head of the printer. You could try clicking on ‘start’ then go to ‘settings’ and then ‘printers’. Select your printer and right click on it and go to ‘properties’. Check to see if there is any such software installed.
Error code: 1200
This error code is commonly associated with the Dell 922 printer. Usually you might see the cartridge moving front and back and slamming itself against the printer. You need to tighten the strings located on the back of the printer and then it should work fine.
Error message: Parallel port maybe used by another application
This is an error message commonly found when you are trying to make a second scanning operation. Try downloading the printer driver according to your specific operating system. You could also try setting a different parallel port in the BIOS.
About the Author:
This Article is written by James Kara Murat from PrintCountry.com, the contributor of Printer Reviews. More information on the subject is at Dell Laser Printer Error Codes, How to Fix Them, and related resources can be found at Dell Ink Cartridges.
Error code: 004-332
This type of error code implies that you need to restart the printer again. However, do check to see if toner cartridges are seated in the proper position. Also ensure that they have been locked in. This is an error commonly associated with the Dell 3100cn laser printer.
Error code: 016-370
This is yet another error message asking you to restart the printer. You need to switch off the printer and then connect it via the USB cable. Press the hold and cancel buttons simultaneously. Then power on the printer again. On your LCD display you should typically see a message saying ‘ready for download mode’. You will then need to initialize the firmware update process.
Error code: 009-360
Sometimes the Dell laser printer only recognizes the yellow toner as ‘missing’. Hence you need to replace the Dell toner with a new one. It can happen when the toner is a remanufactured one with a different chip.
Error type: Not printing black text
This type of error happens because of a problem with the power supply. You need to check if the I/O cable is connected properly or not and that all connections are in place.
Error type: Printing text in red
At certain times you might be able to print perfectly well the first two times and then you see the text being covered in red color. This can happen if the unit is still not properly clean. You could try cleaning the tube.
Error message: Insert yellow toner
Sometimes in spite of replacing the yellow toner in your Dell 5100 cn laser printer you might still get this error message. Try to change the black cartridge. You could also check to see if the toner cartridges are locked appropriately.
Error message: Print head error
This type of error message typically happens when the printer head is not clean enough. You could try installing software that is used to clean the head of the printer. You could try clicking on ‘start’ then go to ‘settings’ and then ‘printers’. Select your printer and right click on it and go to ‘properties’. Check to see if there is any such software installed.
Error code: 1200
This error code is commonly associated with the Dell 922 printer. Usually you might see the cartridge moving front and back and slamming itself against the printer. You need to tighten the strings located on the back of the printer and then it should work fine.
Error message: Parallel port maybe used by another application
This is an error message commonly found when you are trying to make a second scanning operation. Try downloading the printer driver according to your specific operating system. You could also try setting a different parallel port in the BIOS.
About the Author:
This Article is written by James Kara Murat from PrintCountry.com, the contributor of Printer Reviews. More information on the subject is at Dell Laser Printer Error Codes, How to Fix Them, and related resources can be found at Dell Ink Cartridges.
Subscribe to:
Posts (Atom)